esphome:
  name: parksensor
  platform: ESP8266
  board: d1_mini

captive_portal:

wifi:
  ssid: "YOUR-WIFI-SSID"
  password: "YOUR-WIFI-KEY"

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Abstandssensor Fallback Hotspot"
    password: "FALLBACK-WIFI-KEY"
  manual_ip:
    # Set this to the IP of the ESP
    static_ip: 192.168.10.136
    # Set this to the IP address of the router. Often ends with .1
    gateway: 192.168.10.1
    # The subnet of the network. 255.255.255.0 works for most home networks.
    subnet: 255.255.255.0
    dns1: 192.168.10.1

globals:
    - id: active
      type: bool
      restore_value: no
      initial_value: "false"


mqtt:
  broker: your.mqtt.broker.org
  topic_prefix: "esphome"
  on_json_message:
    topic: hm/status/Garage_Licht/STATE
#    topic: hm/status/1OG_Flur_Licht/STATE
    then:
      - lambda: !lambda |-
          bool state = false;
          if (x.containsKey("val"))
            state = x["val"];
          id(active) = state;



# Enable logging
logger:
  level: INFO
  
# Enable Home Assistant API
# api:

web_server:
  port: 80

ota:
  password: "YOUR-OTA-PASSWORD"

uart:
  rx_pin: GPIO12
  tx_pin: GPIO13
  baud_rate: 9600
  id: uart_mhz19
  
sensor:
  - platform: ultrasonic
    id: us_sensor
    trigger_pin: D0
    echo_pin: D1
    update_interval: 0.5s
    name: "Ultrasonic Sensor"
    on_value:
      then:
        - if:
            condition:
              lambda: 'return !id(active);'
            then:
              - light.turn_off: 
                  id: led_ring
        - if:
            condition:
              lambda: 'return (id(active) && (id(us_sensor).state >= id(poti).state*1.5));'
            then:
              - light.turn_on: 
                  id: led_ring
                  red: 0%
                  green: 100%
                  blue: 0%
        - if:
            condition:
              lambda: 'return ( id(active) && ((id(us_sensor).state) < (id(poti).state*1.5) && (id(us_sensor).state >= id(poti).state)) );'
            then:
              - light.turn_on: 
                  id: led_ring
                  red: 100%
                  green: 100%
                  blue: 0%
        - if:
            condition:
              lambda: 'return ( id(active) && (id(us_sensor).state < id(poti).state));'
            then:
              - light.turn_on: 
                  id: led_ring
                  red: 100%
                  green: 0%
                  blue: 0%
                
  

  - platform: adc
    id: poti
    pin: A0
    name: "Potentiomenter"
    update_interval: 1s
    filters:
    - lambda: return x;
    unit_of_measurement: "m"

light:
  - platform: neopixelbus
    id: led_ring
    type: GRB
    variant: WS2812
    pin: GPIO3
    num_leds: 8
    default_transition_length: 0.1s
    name: "NeoPixel Light"