forked from smash/co2ampel
131 lines
3.7 KiB
YAML
131 lines
3.7 KiB
YAML
esphome:
|
|
name: co2_sensor
|
|
platform: ESP32
|
|
board: esp32doit-devkit-v1
|
|
on_boot:
|
|
- display.page.show: boot
|
|
|
|
logger:
|
|
level: DEBUG
|
|
wifi:
|
|
ssid: !secret wifi_ssid
|
|
password: !secret wifi_passwd
|
|
|
|
mqtt:
|
|
broker: mqtt.unhb
|
|
birth_message:
|
|
topic: co2_sensor/status
|
|
payload: online
|
|
will_message:
|
|
topic: co2_sensor/status
|
|
payload: offline
|
|
|
|
uart:
|
|
rx_pin: GPIO17
|
|
tx_pin: GPIO16
|
|
baud_rate: 9600
|
|
id: uart_mhz19
|
|
|
|
light:
|
|
- platform: neopixelbus
|
|
pin: GPIO4
|
|
num_leds: 12
|
|
name: "ws2812 ring"
|
|
id: "ws2812"
|
|
restore_mode: ALWAYS_OFF
|
|
|
|
output:
|
|
- platform: ledc
|
|
pin: GPIO12
|
|
id: buzzer
|
|
|
|
sensor:
|
|
- platform: mhz19
|
|
co2:
|
|
name: "MH-Z19 CO2"
|
|
id: mhz19_co2
|
|
on_value:
|
|
then:
|
|
if:
|
|
condition:
|
|
sensor.in_range:
|
|
id: mhz19_co2
|
|
above: 0
|
|
below: 800
|
|
then:
|
|
- light.turn_off:
|
|
id: ws2812
|
|
- display.page.show: co2
|
|
else:
|
|
if:
|
|
condition:
|
|
sensor.in_range:
|
|
id: mhz19_co2
|
|
above: 800
|
|
below: 1500
|
|
then:
|
|
- light.turn_on:
|
|
id: ws2812
|
|
brightness: 80%
|
|
red: 50%
|
|
green: 50%
|
|
blue: 0%
|
|
else:
|
|
if:
|
|
condition:
|
|
sensor.in_range:
|
|
id: mhz19_co2
|
|
above: 1500
|
|
then:
|
|
- light.turn_on:
|
|
id: ws2812
|
|
brightness: 100%
|
|
red: 100%
|
|
green: 0%
|
|
blue: 0%
|
|
- output.turn_on: buzzer
|
|
- output.ledc.set_frequency:
|
|
id: buzzer
|
|
frequency: "5000Hz"
|
|
- output.set_level:
|
|
id: buzzer
|
|
level: "80%"
|
|
- delay: 500ms
|
|
- output.turn_off: buzzer
|
|
- lambda: |-
|
|
static int num_executions = 0;
|
|
ESP_LOGD("main", "I am at execution number %d", num_executions);
|
|
num_executions += 1;
|
|
|
|
|
|
|
|
temperature:
|
|
name: "MH-Z19 Temperature"
|
|
id: mhz19_temp
|
|
update_interval: 30s
|
|
automatic_baseline_calibration: false
|
|
uart_id: uart_mhz19
|
|
|
|
i2c:
|
|
sda: GPIO21
|
|
scl: GPIO22
|
|
|
|
font:
|
|
- file: "font.ttf"
|
|
id: cust_font
|
|
size: 28
|
|
|
|
display:
|
|
- platform: ssd1306_i2c
|
|
model: "SSD1306 128x64"
|
|
address: 0x3C
|
|
brightness: 100%
|
|
update_interval: 30s
|
|
pages:
|
|
- id: boot
|
|
lambda: |-
|
|
it.printf(64, 32, id(cust_font), COLOR_ON, TextAlign::TOP_CENTER, "starte...");
|
|
- id: co2
|
|
lambda: |-
|
|
it.printf(64, 32, id(cust_font), COLOR_ON, TextAlign::TOP_CENTER, "%.0fPPM", id(mhz19_co2).state);
|
|
# it.printf(64, 40, id(cust_font),TextAlign::TOP_CENTER, "%.0f°C", id(mhz19_temp).state);
|