forked from smash/co2ampel
151 lines
4.5 KiB
YAML
151 lines
4.5 KiB
YAML
substitutions:
|
|
node_name: !env_var co2ampel
|
|
|
|
esphome:
|
|
name: 'co2ampel_${node_name}'
|
|
platform: ESP32
|
|
board: esp32doit-devkit-v1
|
|
on_boot:
|
|
- display.page.show: boot
|
|
on_loop:
|
|
- display.page.show: co2
|
|
|
|
ota:
|
|
safe_mode: true
|
|
password: !secret ota_passwd
|
|
|
|
wifi:
|
|
ssid: !secret wifi_ssid
|
|
password: !secret wifi_passwd
|
|
ap:
|
|
ssid: co2ampel
|
|
password: ''
|
|
|
|
captive_portal: null
|
|
|
|
mqtt:
|
|
broker: co2.cyber23.de
|
|
topic_prefix: 'co2ampel/${node_name}'
|
|
birth_message:
|
|
topic: 'co2ampel/${node_name}/status'
|
|
payload: online
|
|
will_message:
|
|
topic: 'co2ampel/${node_name}/status'
|
|
payload: offline
|
|
|
|
uart:
|
|
rx_pin: GPIO16
|
|
tx_pin: GPIO17
|
|
baud_rate: 9600
|
|
id: uart_mhz19
|
|
|
|
light:
|
|
- platform: fastled_clockless
|
|
chipset: WS2812B
|
|
pin: GPIO4
|
|
num_leds: 12
|
|
max_refresh_rate: 500ms
|
|
rgb_order: GRB
|
|
name: ws2812 ring
|
|
id: ws2812
|
|
restore_mode: ALWAYS_OFF
|
|
|
|
output:
|
|
- platform: ledc
|
|
pin: GPIO12
|
|
id: buzzer
|
|
|
|
sensor:
|
|
- platform: mhz19
|
|
update_interval: 10s
|
|
automatic_baseline_calibration: true
|
|
uart_id: uart_mhz19
|
|
temperature:
|
|
name: '${node_name} Temperature'
|
|
id: mhz19_temp
|
|
co2:
|
|
name: '${node_name} PPM'
|
|
id: mhz19_co2
|
|
on_value:
|
|
then:
|
|
if:
|
|
condition:
|
|
sensor.in_range:
|
|
id: mhz19_co2
|
|
above: 0
|
|
below: 800
|
|
then:
|
|
- light.turn_on:
|
|
id: ws2812
|
|
brightness: 80%
|
|
red: 0%
|
|
green: 100%
|
|
blue: 0%
|
|
- display.page.show: co2
|
|
else:
|
|
if:
|
|
condition:
|
|
sensor.in_range:
|
|
id: mhz19_co2
|
|
above: 800
|
|
below: 1000
|
|
then:
|
|
- light.turn_on:
|
|
id: ws2812
|
|
brightness: 80%
|
|
red: 50%
|
|
green: 40%
|
|
blue: 0%
|
|
- display.page.show: co2
|
|
else:
|
|
if:
|
|
condition:
|
|
sensor.in_range:
|
|
id: mhz19_co2
|
|
above: 1000
|
|
then:
|
|
- light.turn_on:
|
|
id: ws2812
|
|
brightness: 100%
|
|
red: 100%
|
|
green: 0%
|
|
blue: 0%
|
|
- delay: 500ms
|
|
- light.toggle: ws2812
|
|
- delay: 500ms
|
|
- light.toggle: ws2812
|
|
- delay: 500ms
|
|
- light.toggle: ws2812
|
|
- delay: 500ms
|
|
- light.toggle: ws2812
|
|
- lambda: >-
|
|
static int num_executions = 0;
|
|
ESP_LOGD("main", "I am at execution number %d", num_executions);
|
|
num_executions += 1;
|
|
- display.page.show: co2
|
|
i2c:
|
|
sda: GPIO21
|
|
scl: GPIO22
|
|
|
|
font:
|
|
- file: font.ttf
|
|
id: cust_font
|
|
size: 65
|
|
|
|
display:
|
|
- platform: ssd1306_i2c
|
|
model: SSD1306 128x64
|
|
address: 60
|
|
brightness: 100%
|
|
update_interval: 10s
|
|
pages:
|
|
- id: boot
|
|
lambda: |-
|
|
it.printf(64, 0, id(cust_font), COLOR_ON, TextAlign::TOP_CENTER,":-)");
|
|
- id: co2
|
|
lambda: |-
|
|
int ergb;
|
|
ergb = id(mhz19_co2).state;
|
|
it.printf(64, 0, id(cust_font), COLOR_ON, TextAlign::TOP_CENTER, "%.0i", ergb);
|
|
# it.printf(64, 16, id(cust_font), COLOR_ON,TextAlign::TOP_CENTER, "%.0fPPM", id(mhz19_co2).state);
|
|
# it.printf(64, 40, id(cust_font),TextAlign::TOP_CENTER,"%.0f°C", id(mhz19_temp).state);
|