Moved logos into sep. folder.

co2sensor.yaml

@@ -1,36 +1,33 @@
 substitutions:
   node_name: !env_var co2ampel 
-
 esphome:
-   name: 'co2ampel_${node_name}'
+    name: co2ampel_${node_name}
     platform: ESP32
     board: esp32doit-devkit-v1 
     on_boot:
                - display.page.show: boot
-   on_loop:
-      - display.page.show: co2
-
 ota:
-   safe_mode: true
+  safe_mode: True
   password: !secret ota_passwd 
 
+
+logger:
+    level: DEBUG
 wifi:
     ssid: !secret wifi_ssid
     password: !secret wifi_passwd
     ap:
-      ssid: co2ampel
+     ssid: "co2ampel"
-      password: ''
+     password: ""
-
+captive_portal:
-captive_portal: null
-
 mqtt:
   broker: co2.cyber23.de
-   topic_prefix: 'co2ampel/${node_name}'
+  topic_prefix: co2ampel/${node_name}
   birth_message:
-      topic: 'co2ampel/${node_name}/status'
+    topic: co2ampel/${node_name}/status
     payload: online
   will_message:
-      topic: 'co2ampel/${node_name}/status'
+   topic: co2ampel/${node_name}/status
    payload: offline
 
 uart:
@@ -40,14 +37,11 @@ uart:
   id: uart_mhz19
 
 light:
-   -  platform: fastled_clockless
+  - platform: neopixelbus
-      chipset: WS2812B
     pin: GPIO4
     num_leds: 12
-      max_refresh_rate: 500ms
+    name: "ws2812 ring"
-      rgb_order: GRB
+    id: "ws2812"
-      name: ws2812 ring
-      id: ws2812
     restore_mode: ALWAYS_OFF
 
 output:
@@ -61,10 +55,10 @@ sensor:
     automatic_baseline_calibration: true 
     uart_id: uart_mhz19
     temperature:
-         name: '${node_name} Temperature'
+      name: ${node_name} Temperature
       id: mhz19_temp
     co2:
-         name: '${node_name} PPM'
+      name: ${node_name} PPM
       id: mhz19_co2
       on_value:
        then:
@@ -75,12 +69,8 @@ sensor:
                   above: 0
                   below: 800
            then:
-                     -  light.turn_on:
+            - light.turn_off:
                id: ws2812
-                           brightness: 80%
-                           red: 0%
-                           green: 100%
-                           blue: 0%
             - display.page.show: co2
            else:
                 if:
@@ -94,7 +84,7 @@ sensor:
                         id: ws2812
                         brightness: 80%
                         red: 50%
-                                 green: 40%
+                        green: 50%
                         blue: 0%
                      - display.page.show: co2
                  else:
@@ -110,6 +100,15 @@ sensor:
                                                  red: 100%
                                                  green: 0%
                                                  blue: 0%
+                                       # - output.turn_on: buzzer
+                                       # - output.ledc.set_frequency:
+                                       #    id: buzzer
+                                       #    frequency: "5000Hz"
+                                       # - output.set_level:
+                                       #    id: buzzer
+                                       #    level: "20%"
+                                       # - delay: 10ms
+                                       # - output.turn_off: buzzer
                                          - delay: 500ms
                                          - light.toggle: ws2812
                                          - delay: 500ms
@@ -118,7 +117,7 @@ sensor:
                                          - light.toggle: ws2812
                                          - delay: 500ms
                                          - light.toggle: ws2812
-                                 -  lambda: >-
+                                         - lambda: |-
                                             static int num_executions = 0;
                                             ESP_LOGD("main", "I am at execution number %d", num_executions);
                                             num_executions += 1;
@@ -128,14 +127,14 @@ i2c:
   scl: GPIO22
 
 font:
-   -  file: font.ttf
+  - file: "font.ttf"
     id: cust_font
-      size: 65
+    size: 70
 
 display:
   - platform: ssd1306_i2c
-      model: SSD1306 128x64
+    model: "SSD1306 128x64"
-      address: 60
+    address: 0x3C
     brightness: 100%
     update_interval: 10s
     pages:
@@ -145,7 +144,7 @@ display:
             - id: co2
               lambda: |-
                int ergb;
-               ergb = id(mhz19_co2).state;
+               ergb = id(mhz19_co2).state/100;
                it.printf(64, 0, id(cust_font), COLOR_ON, TextAlign::TOP_CENTER, "%.0i", ergb);
 #               it.printf(64, 16, id(cust_font), COLOR_ON, TextAlign::TOP_CENTER, "%.0fPPM", id(mhz19_co2).state);
 #            it.printf(64, 40, id(cust_font),TextAlign::TOP_CENTER, "%.0f°C", id(mhz19_temp).state);

lasercut_case/stiftungsprojekt/Pattern_description.md

@@ -1,8 +0,0 @@
-|           | Backplates | Frontplates | Topplates | Bottomplates | Circles | Side L | Side R | Deckel |
-|-----------|------------|-------------|-----------|--------------|---------|--------|--------|--------|
-| Pattern 1 |         18 |          17 |         2 |            2 |         |        |        |        |
-| Pattern 2 |            |             |           |              |     135 |        |        |        |
-| Pattern 3 |            |             |           |              |         |     40 |     40 |        |
-| Pattern 4 |            |             |        40 |           40 |         |        |        |        |
-| Pattern 5 |            |             |        20 |           20 |         |     20 |     20 |        |
-| Pattern 6 |            |             |           |              |         |        |        |    135 |